SERVICING THE SCOREBOARD

While your scoreboard was designed for years of trouble-free operation, some problems may occasionally occur.  Electro-Mech Scoreboard Company offers onsite service in some areas.  In other areas, we can help you contact an independent service technician.  In areas in which service is not available from Electro-Mech Scoreboard Company, we will make every effort to answer your questions.  Our trained personnel at Electro-Mech Scoreboard Company are ready to answer your questions from Monday to Friday during the hours of 8 AM to 5 PM Eastern Standard Time.  Be sure to know your scoreboard model number when calling.  Scoreboard replacement parts are always available.  Damaged parts can usually be repaired at a significant cost savings.  Our convenient toll free number is listed at the bottom of every page in this manual.

COMPONENT REPLACEMENT

LED Digits And Indicators Replacement

The LEDs that form digits and indicators are soldered on circuit boards mounted behind metal masks.  Do not attempt to replace individual LEDs.  In case of a malfunction, the entire LED circuit board must be removed.  To avoid damage to the LED driver module, always turn off the power to the scoreboard when removing or replacing LED digits and indicators.  Figure 10 shows the components of a LED digit assembly.  LED indicator assemblies are similar in construction.

Figure 10  LED Digit Assembly

1. The ribbon cable that connects to the rear of the circuit board is not designed to support the weight of the assembly.
2. Damage to the ribbon cable may create short circuit paths that will damage the LED driver module.
3. Place the assembly on a flat surface and remove the 6-32 kep lock nuts that hold the circuit board in place.
4. Remove the circuit board.
5. Align the mounting holes in the circuit board with the threaded studs on the mask and install the replacement digit on the mask.
6. Refer to figure 11 in order to plug the ribbon cable IDC connector onto the circuit board in the proper orientation.

Figure 11  LED Digit Ribbon Cable Connection Diagram

1. The other circuit board has one header and may only be used for BONUS 1.

Figure 12  BONUS 1 and BONUS 2 Ribbon Cable Connection Diagram

Horn Replacement

1. Remove the machine screws that fasten the mask to the face of the scoreboard.
2. Pull the horn assembly out of the scoreboard and cut the two wires leading up to the rear of the horn assembly.
3. Splice the new horn assembly wires to the two wires inside the scoreboard.
4. Install the horn assembly and fasten it to the scoreboard face using the machine screws.

The components that control the middle section of the scoreboard are located behind the PERIOD panel.  Figure 13 shows the view behind the PERIOD panel.

Figure 13  Middle Section Electronics

LED Driver Module Replacement

Electrical connections to the LED DRIVER MODULE are made with ribbon cable polarized IDC sockets and locking ramp crimp terminal housings that mate with jacks on the module.  The module is secured inside the scoreboard with four machine screws.

1. Do not cut the plastic tie wraps around the ribbon cables.
   1. Remove the four screws.
   2. Remove the module from the scoreboard.
   3. Insert the replacement module in the scoreboard.
   4. Secure the module with the four screws.
   5. Insert the plugs into the jacks on the module.

To avoid damage to the module, always turn off the power to the scoreboard when removing or replacing it.

LPS-130VA LED POWER SUPPLY MODULE FUNCTIONS

Figure 14 shows the location of the LPS-130VA Power Supply Module fuses and jack pins.  The table following the figure lists the fuse ratings, functions, and part numbers.

Figure 14  LPS-130VA POWER SUPPLY MODULE

LPS-130VA FUSES

Note:  Other manufacturer’s fuses may be substituted for the Bussmann fuses.

LED Power Supply Module Replacement

Electrical connections to the LED POWER SUPPLY MODULE are made with keyed plugs that mate with jacks on the side of the module.  The module is secured inside the scoreboard with two machine screws.

1. Disconnect the plugs from the jacks on the module.
2. Remove the two machine screws.
   1. Remove the module from the scoreboard.
   2. Insert the replacement module in the scoreboard.
   3. Secure the module with the four screws.
   4. Insert the plugs into the jacks on the side of the module.

To avoid damage to the module, always turn off the power to the scoreboard when removing or replacing it.

The components that control the HOME STAT PANEL section of the scoreboard are located behind the PLAYER FOULS POINTS panel on the right side of the scoreboard.  The components that control the GUEST STAT PANEL section of the scoreboard are located behind the PLAYER FOULS POINTS panel on the left side of the scoreboard.  The components and their functions are identical to the HOME STAT PANEL components.  The LED digit assemblies for the first player number, fouls, and points must be removed before removing the panel.  The following steps describe how to remove the PLAYER FOULS POINTS panel:

1. The ribbon cables that connect to the rear of the assembly are not designed to support the weight of the assembly.
2. Damage to the ribbon cable may create short circuit paths that will damage the LED driver modules.
3. Repeat Steps 1 and 2 for the FOULS and POINTS assemblies.
4. Figure 15 shows the components behind the panel.

Figure 15  HOME Stat Panel Section Electronics